How to Remove Old ADT Panel from Wall?

There can have various reasons you want to remove your old ADT panel from the wall. Of the probable causes, the most common one is that if you want to make the ADT panel update, then you have to remove the old one and replace a new ADT panel on your wall. 

Since removing an old ADT panel from your wall is a sensitive task, you should be more careful and choose the best method to remove it from the wall. Because, while removing the ADT panel from the wall then, sometimes you can find the finished wood, sheetrock, or wall damaged. To avoid these damages and get a smart solution to remove old ADT panels from the wall, you have to follow the article.

Methods: How to Remove Old ADT Panel from Wall?

It is crucial to shut down or bypass the zones that apply to the sensor you have selected to remove. To shut down the selected zone, you must access the command panel security menu. After that, you have to follow the instructions carefully to remove the old ADT panel from your wall. 

1. In this step, you have to select the option ‘’zones’’. This option will open a list of all the active zones of your home. 
2. Then you have to choose the zone you would like to bypass. Now, select the option “bypass” and enter the user code. 
3. In this step, the zone that you have chosen will be bypassed. In addition, without tripping the alarm, you will get the zone safe to remove.

These are the first phrase. When the zone is disabled, then it will be easy to remove the ADT panel from your wall. Now, I will share with you some ideas with which you can implement the task smartly. You can use any of them.

Removing a Wireless ADT Panel from The Wall

If you want to remove a wireless ADT panel from your wall, then you need to have a knife or a razor. Then use the knife or razor to cut through the silicone lining. In this case, you can slide through the adhesive with the help of the knife conveniently. It will also be possible to remove the panel with a putty knife or razor smartly. 

If you have no razor or knife, then it will be okay to use a hot air gun or blow dryer to heat the silicone sufficiently. The air gun or blow dryer can soften the silicone for easier ADT panel removal and cleanup. But if the silicone seems very heavy and you do not want to use a blade, then you can use WD-40 as an effective silicone sealant remover. Because mineral and acetone spirits are very strong silicone digestants and they remove the finish from any paint or wood on the wall. 

Removing Wired ADT Panel from the Wall

You can use a small Philips-head-screwdriver to remove the wired ADT panel from the wall. After removing the wires entirely, then you can leave them for future use or can pull them through the hole to remove them completely. 

But there is some ADT panel that is recessed within a frame. Thus, it is quite difficult to remove them from the frame. But I am here to guide you in a very effective way. 

You must use your finger or a screwdriver to pry the wires. You will see the magnet comes first since the magnet is not connected. Then you can remove the wires. After that, you can come across the panel that is screwed into the sheetrock or wood. Now, just simply remove the magnet to game access to the screws on the base plate of the ADT panel.

How to Remove ADT Keypad from Wall?

A keypad-based alarm system has basically low voltage with the possible expectation of the main control box. To remove the ADT keypad from your wall, it is necessary to cut the main power in your house. Because you need safety that there is zero possibility not to electrocute yourself. So, at first, make sure that the live wires are disconnected from the main and start doing the task. 

You can get two small slots on the unit’s bottom. There is a special key inserted into these two slots that you can open up the unit. Then take a screwdriver and put it in each of the slots. That task will let you pry it away. 

How Do I Decommission My ADT Alarm?

It is a very easy process to decommission your ADT alarm. If you need to decommission your ADT alarm completely, then you should use this instruction. 

To decommission the ADT alarm, you must first locate your alarm panel. The main alarm panel is generally located in the mid-sized white box attached to the wall. Then, locate the fuse spur. You can get the alarm fuse spur next to the alarm panel. After locating the fuse spur, you have to open the small compartment that stays in front of the box. Then make the fuse prizing out. Now, the alarm has lost its main power. The alarm will be running off the battery. After that, by using a screwdriver, open the main alarm panel. 

Inside the alarm panel, you have to locate the battery and remove the x2 terminal wires. After that, the outside bell of the alarm will start ringing for 20 minutes. Then, when the ring is stopped, the alarm will be decommissioned. 

Frequently Asked Questions

How Often Should I Test My ADT system?

It is very necessary to test your ADT system regularly. The experts recommend testing the ADT system every thirty days. However, you should test your ADT system after any changes to internet service, home renovations, or phone service.

Will My Alarm System Work after Losing Power?

Why not! The alarm system will work if you lose power for several hours. But the system battery power will be gradually lower. The system will also display the low battery by message on the keypad.  

Should I Replace or Recharge a Low Battery?

A low battery indicates that your battery will give a chance to recharge itself. So, in this situation, the battery will recharge itself only once when the AC power has been restored. But you have to replace your lower battery when the battery signal does not disappear after restoring the backup battery for 24 hours to 48 hours. 

Conclusion

It is very crucial to know how to remove the old ADT panel from your wall. Because it is very common to replace the old one. When you need to replace the ADT sensor, it can give you a contact repair kit. You can achieve the ADT contact repair kit by contacting the customer service center of ADT. But you also have the option to purchase double-sided adhesive tape, a new sensor, and silicone sealant.